Critical Review on and Analysis of Solar Powered Electric Vehicle Charging Station.

Geetha Palani Kannan, S. Usha

Abstract


Electric vehicles (EV) are the future medium of transportation system due to the heightening of conventional fuel costs of petrol or diesel-based vehicles. Hence the energy demand will be higher when EVs are brought into the public transportation system. In this review paper, the solar-powered charging station for an electric vehicle is evaluated by tilting the solar panel at a different angle, then the maximum efficiency and power that can be obtained from the solar light depending on the wavelength of the sunlight are analyzed. Photovoltaic (PV) panels can be able to charge electric vehicles (EVs) sustainably. Then using the solar potential in office buildings for EV charging at work, as well as it takes the long parking time at work, open the route for the deployment of vehicle-to-grid (V2G) technology. Various types of system architectures for an EV-PV charger are researched and compared in this paper. A comparison of power converters that integrate the EV and PV for V2G operation is done and based mainly on the system architecture, converter topology, isolation, and bidirectional power capability. The fundamental terminologies of charging stations, such as charging station types and levels, are reviewed in this paper. To tackle these issues, a variety of technologies are reviewed, as well as a brief overview of lithium-ion type battery for charging methodologies and the Battery Management energy System (BMS). The advantages of the EV over fuel vehicles have been outlined and the impact of the coil design and coil detection system for EV is also discussed here. Prospects and challenges involved in recent technologies for efficient systems in wireless charging systems are also emphasized in this article.


Keywords


Electric vehicle (EV), Electric vehicle charging, wireless power transmission, Battery, Solar panels, Battery Energy Storage System, converters, Coil design.

Full Text:

PDF

References


A Gayathri1, C Prasanna1, M Priyanka1, M Rahul1, K Mohamed Abdullah1 1Department of EEE, Sri Krishna College of Technology, Coimbatore, Tamilnadu, India “ Solar Based Charging Station for E-Vehicle” in 2021, Journal of Physics: Conference Series, 1916 (2021) 012130, 1742-6596/1916/1/012130.

Mohammad EkramulKabir, Student Member, IEEE, ChadiAssi, Fellow, IEEE, Mosaddek Hossain Kamal Tushar, Member, IEEE, and Jun Yan, Member, IEEE “Optimal Scheduling of EV Charging at a Solar Power-Based Charging Station” IEEE Systems Journal in 2020, Volume number:14, Page number: 4221 – 4231, Sept. 2020

H.-Y. Mak, Y. Rong, and Z.-J. M. Shen, ‘‘Infrastructure planning for electric vehicles with battery swapping,’’ Manage. Sci., vol. 59, no. 7, pp. 1557–1575, 2013.

M. Eshani, Y. GAO, S. E. Gay, and A. Emadi, ‘‘Modern electric, hybrid electric and fuel cell vehicles,’’ in Fundamentals, Theory, and Design. Boca Raton, FL, USA: CRC Press, 2005.

A. Emadi, M. Ehsani, and J. M. Miller, Vehicular Electric Power Systems: Land, Sea, Air, and Space Vehicles. Boca Raton, FL, USA: CRC Press, 2003.

M. Yilmaz and P. T. Krein, ‘‘Review of battery charger topologies, charging power levels, and infrastructure for plug-in electric and hybrid vehicles,’’ IEEE Trans. Power Electron., vol. 28, no. 5, pp. 2151–2169, May 2013.

Chen Duan, Member, IEEE, Caisheng Wang, Senior Member, IEEE, Zongzheng Li, Jianfei Chen, Member, IEEE, Shidao Wang, Adrian Snyder and Chenguang Jiang “A Solar Power Assisted Battery Balancing System For Electric Vehicles ”in IEEE Transactions on Transportation Electrification, Volume: 4, Issue: 2, Page number: 432 – 443, June 2018.

Dong Ji, MingsongLv, Jiayu Yang, Wang Yi “Optimizing the Locations and Sizes of Solar Assisted Electric Vehicle Charging Stations in an Urban Area” in IEEE transaction 2020, Volume: 8, Page number: 112772 – 112782 in 2020.

Daisy Ranawat, M P R Prasad “A Review on Electric Vehicles with the perspective of Battery Management System” in National Institute of Technology Kurukshetra Department of Electrical Engineering, third International Conference on Electrical and Electronics, Communication, Computer Technologies and Optimization Techniques (ICEECCOT) 14-15, in December 2018.

Joshua Traube, Member, IEEE, Fenglong Lu, Member, IEEE, DraganMaksimovic, Senior Member, IEEE, Joseph Mossoba, Matthew Kromer, Peter Faill, Stan Katz, BogdanBorowy, Steve Nichols, and Leo Casey, “Mitigation of Solar Irradiance Intermittency in Photovoltaic Power Systems With Integrated Electric-Vehicle Charging Functionality” in IEEE Transactions On Power Electronics, Vol. 28, No. 6, June 2013

GamalAlkawsi, YahiaBaashar, Dallatu Abbas U, Ammar Ahmed Alkahtani, SiehKiongTiong “Review of Renewable Energy-Based Charging Infrastructure for Electric Vehicles” Appl. Sci. 2021, 11, 3847 in2021.

Geneva Zhang1, Jianming Lai1, Shijun Feng1 and Weimin Shi2 1 Shanghai Lianfu New Energy S&T Co., Ltd., 1003 Wangqiao Road, Shanghai, 201201, China, qfsu@163.com 2 Department of Electronics and Information Materials, Shanghai University, 149 Yanchang Road, Shanghai, 200072, China “Green Solar Electric Vehicle Changing the Future Lifestyle of Human”.

MdSohailTanveer, Sunil Gupta, Rahul Rai, Neeraj Kumar Jha “Solar based electric vehicle charging station”2nd International Conference on Power Energy, Environment and Intelligent Control (PEEIC) in 2019, 978-1-7281-1793-5/19/IEEE.

SAE Standard J1772, “SAE Electric Vehicle and Plug-in Hybrid Electric Vehicle Conductive Charge Coupler,” 2010.

“Standard IEC 62196 - Plugs, socket-outlets, vehicle connectors, and vehicle inlets - Conductive charging of electric vehicles,” 2014.

N. Naghizadeh and S. S. Williamson, “A comprehensive review of power electronic converter topologies to integrate photovoltaics (PV), AC grid, and electric vehicles,” in 2013 IEEE Transportation Electrification Conference and Expo (ITEC), 2013, pp. 1–6.

G. Gamboa, C. Hamilton, R. Kerley, S. Elmes, A. Arias, J. Shen, and I. Batarseh, “Control strategy of a multi-port, grid-connected, direct-DC PV charging station for plug-in electric vehicles,” in 2010 IEEE Energy Conversion Congress and Exposition, 2010, pp. 1173–1177.

C. Hamilton, G. Gamboa, J. Elmes, R. Kerley, A. Arias, M. Pepper, J. Shen, and I. Batarseh, “System architecture of a modular direct-DC PV charging station for plug-in electric vehicles,” in IECON 2010 - 36th Annual Conference on IEEE Industrial Electronics Society, 2010, pp. 2516–2520.

M. Vaidya, E. K. Stefanakos, B. Krakow, H. C. Lamb, T. Arbogast, and T. Smith, “Direct DC-DC electric vehicle charging with a grid-connected photovoltaic system,” in Conference Record of the IEEE Photovoltaic Specialists Conference, 1996, pp. 1505–1508.

Z. Qian, O. Abdel-Rahman, C. Hamilton, M. Batarseh, and I. Batarseh, “An integrated four-port converter for compact and efficient hybrid power systems,” in Proceedings of 2010 IEEE International Symposium on Circuits and Systems, 2010, pp. 2207–2210.

Z. Qian, O. Abdel-Rahman, H. Hu, and I. Batarseh, “An integrated three-port inverter for stand-alone PV applications,” in 2010 IEEE Energy Conversion Congress and Exposition, 2010, pp. 1471–1478.

J. G. J. G. Ingersoll and C. A. Perkins, “The 2.1 kW photovoltaic electric vehicle charging station in the city of Santa Monica, California,” in Conference Record of the IEEE Photovoltaic Specialists Conference, 1996, pp. 1509–1512.

S. Mesentean, W. Feucht, H.-G. Kula, and H. Frank, “Smart charging of electric scooters for a home to work and home to education transports from grid-connected photovoltaic-systems,” in 2010 IEEE International Energy Conference, 2010, pp. 73–78.

“Solar electric vehicle charging station, University of Iowa.” [Online] http://facilities.uiowa.edu/uem/renewableenergy/solar-energy.html.

Laboratory Oak Ridge National, “Solar-Assisted Electric Vehicle Charging Stations,” 2011.

P. J. Tulpule, V. Marano, S. Yurkovich, and G. Rizzoni, “Economic and environmental impacts of a PV powered workplace parking garage charging station,” Appl. Energy, vol. 108, pp. 323–332, Aug. 2013.

P. Tulpule, V. Marano, S. Yurkovich, and G. Rizzoni, “Energy economic analysis of PV based charging station at the workplace parking garage,” in IEEE 2011 EnergyTech, 2011, pp. 1–6.

F. Turki, A. Guetif, and C. Sourkounis, “Contactless charging electric vehicles with renewable energy,” in 2014 5th International Renewable Energy Congress (IREC), 2014, pp. 1–6.

M. Benaouadj, A. Aboubou, M. Becher, M. Y. Ayad, and M. Bahri, “Recharging of batteries/supercapacitors hybrid source for electric vehicles application using photovoltaic energy in a stand-alone point,” in 2012 First International Conference on Renewable Energies and Vehicular Technology, 2012, pp. 161–166.

G. Carli and S. S. Williamson, “Technical Considerations on Power Conversion for Electric and Plug-in Hybrid Electric Vehicle Battery Charging in Photovoltaic Installations,” IEEE Trans. Power Electron., vol. 28, no. 12, pp. 5784–5792, Dec. 2013.

Z. Rasinab and M. F. Rahman, “Grid-connected quasi-Z-source PV inverter for an electric vehicle charging station,” in 2013 International Conference on Renewable Energy Research and Applications (ICRERA), 2013, pp. 627–632.

Z. Rasin, K. Ahsanullah, and M. F. Rahman, “Design and simulation of quasi-Z-source grid-connected PV inverter with bidirectional power flow for battery storage management,” in IECON 2013 - 39th Annual Conference of the IEEE Industrial Electronics Society, 2013, pp. 1589– 1594.

P. Goli and W. Shireen, “PV Integrated Smart Charging of PHEVs Based on DC-Link Voltage Sensing,” IEEE Trans. Smart Grid, vol. 5, no. 3, pp. 1421–1428, May 2014.

A. Nagarajan and W. Shireen, “Grid-connected residential photovoltaic energy systems with Plug-In Hybrid Electric Vehicles (PHEV) as energy storage,” in IEEE PES General Meeting, 2010, pp. 1–5.

Lei Shi, HaipingXu, Dongxu Li, Zuzhi Zhang, and Yuchen Han, “The photovoltaic charging station for an electric vehicle to grid application in Smart Grids,” in 2012 IEEE 6th International Conference on Information and Automation for Sustainability, 2012, pp. 279–284.

H. Krishnaswami and N. Mohan, “Three-Port Series Resonant DC-DC Converter to Interface Renewable Energy Sources With Bidirectional Load and Energy Storage Ports,” IEEE Trans. Power Electron., vol. 24, no. 10, pp. 2289–2297, Oct. 2009.

T.-E. Stamati and P. Bauer, “On-road charging of electric vehicles,” in 2013 IEEE Transportation Electrification Conference and Expo (ITEC), 2013, pp. 1–8.

S. Divyapriya, R. Vijayakumar, et al., “Design of residential plugin electric vehicle charging station with a time of use tariff and IoT technology,” in 2018 International Conference on Soft-computing and Network Security (ICSNS). IEEE, 2018, pp. 1–5.

A. Santos, N. McGuckin, H. Y. Nakamoto, D. Gray, and S. Liss, “Summary of travel trends: 2009 national household travel survey,” Tech. Rep., 2011.

J. Babic, A. Carvalho, W. Ketter, and V. Podobnik, “Evaluating policies for parking lots handling electric vehicles,” IEEE Access, vol. 6, pp. 944–961, 2017.

S. Habib, M. M. Khan, F. Abbas, L. Sang, M. U. Shahid, and H. Tang, “A comprehensive study of implemented international standards, technical challenges, impacts and prospects for electric vehicles,” IEEE Access, vol. 6, pp. 13 866–13 890, 2018.

A. S. Varghese, P. Thomas, and S. Varghese, “An efficient voltage control strategy for fast charging of plug-in electric vehicle,” in 2017 Innovations in Power and Advanced Computing Technologies (I-PACT). IEEE, 2017, pp. 1–4.

D. Zhang, F. Wen, and J. Huang, “Optimal planning of battery swap stations,” 2012.

S. Habib, M. M. Khan, F. Abbas, L. Sang, M. U. Shahid, and H. Tang, “A comprehensive study of implemented international standards, technical challenges, impacts and prospects for electric vehicles,” IEEE Access, vol. 6, pp. 13 866–13 890, 2018.

F. Zhang, X. Zhang, M. Zhang, and A. S. Edmonds, “Literature review of electric vehicle technology and its applications,” in 2016 5th International Conference on Computer Science and Network Technology (ICCSNT). IEEE, 2016, pp. 832–837.

M. Yilmaz and P. Krein, “Review of charging power levels and infrastructure for plug-in electric and hybrid vehicles and commentary on unidirectional charging,” in IEEE International Electrical Vehicle Conference, 2012.

Y. J. Jang, “Survey of the operation and system study on wireless charging electric vehicle systems,” Transportation Research Part C: Emerging Technologies, vol. 95, pp. 844–866, 2018.

N. Shinohara, “Wireless power transmission progress for electric vehicle in Japan,” in 2013 IEEE Radio and Wireless Symposium. IEEE, 2013, pp. 109–111.

“Charging Time of Battery,” https://pod-point.com/guides/driver/ how-long-to-charge-an-electric-car/, 2019, [Online; accessed 27-July2019].

Tan, N.M.L.; Abe, T.; Akagi, H. “Design and Performance of a Bidirectional Isolated DC-DC Converter for a Battery Energy Storage System” in IEEE Trans. Power Electron in the year of 2012, 27, 1237–1248. [CrossRef]

. Ingole, J.N.; Choudhary, M.A.; Kanphade, R.D. “Pic Based Solar Charging Controller for Battery”. Int. J. Eng. Sci. Technol. 2012, 4, 384–390.

Liang, X.; Tanyi, E.; Zou, X. “Charging Electric Cars from Solar Energy (Dissertation)”. 2016. Available online: http://urn.kb.se/ resolve? Urn=urn: NBN: se: bth-11919 (accessed on 10 June 2016).

Mohammad Abdullah Al Mamun, Mohammad Istiak, Khandakar Abdulla Al Mamun, SharifaAkterRukaia “Design and Implementation of a Wireless Charging System for Electric Vehicles” In IEEE Transaction in 2020.

DevendraPatil, IEEE Student Member, John Miller, IEEE Life Fellow, BabakFahimi, IEEE Fellow and Poras T. Balsara, IEEE Fellow and Veda Galigerkere, IEEE Senior Member “A Coil Detection System for Dynamic Wireless Charging of Electric Vehicle” In IEEE Transaction 2019, TTE--2018-11-0275 page number: 1-16.

B. Tierney and A. Grbic, IEEE Trans. “Microwave Theory Tech”. 62, 909- 919 (2014)

B. Tierney and A. Grbic, IEEE Trans. “Antennas Propag”. 62, 3310-3320 (2014)

Resonators for wireless power transfer systems In IEEE Transaction in 2017

S. Cheon, Y. H. Kim, IEEE Trans. Ind. Electron., 58, 7, 2906-2914. (2011)

I. Sasada, J. Appl. Phys., 111, 07E733, (2012)

X. Wang et al., “Analysis and experimental study of wireless power transfer with HTS coil and copper coil as the intermediate resonators system,” Phys. C, Supercond. Appl., vol. 532: pp. 6–12, 2017.

H. Yu et al., “Asymmetry in wireless power transfer between a superconducting coil and a copper coil,” IEEE Trans. Appl. Supercond., vol. 28, no. 3, Apr. 2018, Art. No. 0600606.

X. Wang et al., “Experimental and numerical study of a magnetic resonance wireless power transfer system using superconductor and ferromagnetic metamaterials,” IEEE Trans. Appl. Supercond., vol. 28, no. 5, Aug. 2018, Art. no. 1800206.

I. Jong et al., “Analysis of S-parameter using different materials for the WPT resonance coil,” IEEE Trans. Appl. Superconductors., vol. 28, no. 3, Apr. 2018, Art. No. 0500405.

E. Heo et al., “A wearable textile antenna for wireless power transfer by magnetic resonance,” Textile Res. J., vol. 88, no. 8, pp. 913–921, 2017.

S. H. Kang and C. W. Jung, “Textile resonators with thin copper wire for wearable MR-WPT system,” IEEE Microw. Wireless Compon. Lett. vol. 27, no. 1, pp. 91–93, Jan. 2017

M. Bissannagari et al., “Fully-inkjet-printed Ag-coil/NiZn-ferrite for flexible wireless power transfer module: Rigid sintered ceramic body into flexible form,” Adv. Funct. Mater. vol. 27, no. 31, 2017, Art. No. 1701766

N. J. Grabham et al., “Fabrication techniques for manufacturing flexible coils on textiles for inductive power transfer,” IEEE Sens. J., vol. 18, no. 6, pp. 2599–2606, Mar. 2018.

. Kaouane M. Boukhelifa A. Cheriti A. “Regulated output voltage double switch Buck-Boost converter for photovoltaic energy application”. Int J Hydrogen Energy 2016; 41(45):20847-57.

. Ramirez-Murillo H et aL“An efficiency comparison of fuel-cell hybrid systems based on the versatile buck-boost converter”. IEEE Trans Power Electron 2018; 33(4:1237-46).

. Best V. Singh B. “An adjustable-speed PFC bridgeless buck-boost converter-fed BIDC motor drive”. IEEE Trans Ind Electron 2014; 61(6):2665-77.

. Alonzo JM, Villa J, Vaquero DC, Martinez C, Osorio “It Analysis and design of the integrated double buck-boost converter as a high-power-factor driver for power-led lamps”. IEEE Trans Ind Electron 2012; 59(4)1689-97.

.Blanes JM, Gutierrez R, Garrig6s A, Lizan JL, Cuadrado JM. “Electric vehicle battery life extension using ultracapacitors and an FPGA controlled interleaved buck-boost converter”. IEEE Trans Power Electron 2013; 28 (12):5940-8.

.Lee YJ, Khaligh A, Emadi A. “A compensation technique for smooth transitions in a noninverting buck-boost converter”. IEEE Trans Power Electron 2009; 24 (4):1002-15.

M. Brandl, H. Gall, M. Wenger, V. Lorentz, M. Giegerich, F. Baronti, G. Fantechi, L. Fanucci, R. Roccella, R. Saletti, S. Saponara, A. Thaler, M. Crain, W. Prochazka, ”Batteries and Battery Management Systems for Electric Vehicles,” in Conference: Design, Automation & Test in Europe Conference & Exhibition (DATE) Germany, March 2012.

Juan Dixon, “Energy Storage for Electric Vehicles,” IEEE International Conference on Industrial Technology Chile, March 2010.

Allan Cooper, Patrick Moseley, “Progress in the Development of Lead Acid Batteries for Hybrid Electric Vehicles,” IEEE Vehicle Power and Propulsion Conference Windsor, UK, September 2006.

FrederikEinwächter, Constantinos Sourkounis, “Accessing Flexibility of Electric Vehicles for Smart Grid Integration,” IEEE Ninth International Conference on Ecological Vehicles and Renewable Energies (EVER) Monte Carlo, March 2014.

Sergio Vazquez, Srdjan M. Lukic, Eduardo Galvan, Leopoldo G. Franquelo, Juan M. Carrasco,” Energy Storage Systems for Transport and Grid Applications,” IEEE Transactions on Industrial Electronics, pp. 3881 – 3895, September 2010.

The Boston Consulting Group (BCG) “Batteries for Electric Cars,” 2010.

Srdjan M. Lukic, Jian Cao, Ramesh C. Bansal, Fernando Rodriguez, Ali Emadi, “Energy Storage Systems for Automotive Applications,” IEEE Transactions on Industrial Electronics, pp. 2258 – 2267, May 2008.

Cuicui Yin, Yun Wang, “Research on battery management system in an electric vehicle,” 2012 2nd International Conference on Consumer Electronics, Communications and Networks (CECNet) Yichang, China, April 2012.

Texas instrument, “Intelligent battery management and charging for electric vehicles,” from www.ti.com.

BharathPattipati, Krishna Pattipati, Jon P. Christopherson, SetuMadhaviNamburu, Danil V. Prokhorov, and Liu Qiao, “Automotive Battery Management Systems,” IEEE autotestconusa, September 2008.

Jian Cao, Nigel Schofield, Ali Emadi, “Battery balancing methods: A comprehensive review,” IEEE Vehicle Power and Propulsion Conference China, September 2008.

Hu, Rui, "Battery Management System for Electric Vehicle Applications" Electronic Theses and Dissertations 2011.

ChakibAlaoui, “Solid-State Thermal Management for Lithium-Ion EV Batteries,” IEEE Transactions on Vehicular Technology, pp. 98-107, January 2018.

K. Yang, D.H. Li, S. Chen, and F. Chen, “Thermal model of batteries for electrical vehicles,” Transactions of Beijing Institute of Technology, pp. 782-784, 2008.

. Yufei Chen, Li Song, J.W. Evans, “Modeling studies on battery thermal behavior, thermal runaway, thermal management, and energy efficiency,” IECEC 96. Proceedings of the 31st Intersociety Energy Conversion Engineering Conference Washington, DC, USA, August 1996.

. PengQingfeng, Zhao Han, Liu xinwen, Fang Yunzhou, and Zeng Xiangbing, “Battery thermal management system design and control strategy study for hybrid electric vehicles,” IEEE Conference and Expo Transportation Electrification Asia-Pacific China, September 2014.

The Automotive Research Association of India “Electric Vehicle Conductive DC Charging System”, 2018

Nusrat Chowdhury and Akram Hossain “Optimization of Solar Energy System for the Electric Vehicle” Bangladesh, 2018

G.R. Chandra Mouli, P. Bauer, M. Zeman “System design for a solar-powered electric vehicle charging station”, 2016

Kaveri Markam1, K. Sudhakar2 “Estimation of optimal tilt angle for solar photovoltaic installations in India”, Volume: 03, 2016

Praveen Kumar and Kalyan Das “Potential Need for Electric Vehicles, Charging Station Infrastructure and its Challenges for the Indian Market” Volume 3, 2016

Nikhil Nayak, “ Growth of Electric Vehicle in Indian market by increasing the EV public charging”, Mechanical Department, B.V. College, India, Volume 1, 2015

Bin Ye and Jingjing Jiang “Feasibility Study of a Solar-Powered Electric Vehicle Charging Station Model”, 2015

Gheorghe Badea, Raluca-AndreeaFelseghi “Design and Simulation of Romanian Solar Energy Charging Station for Electric Vehicles” 2018

Hanging Zhao and Andrew Burke “An Intelligent Solar Powered Battery Buffered EV Charging Station with Solar Electricity Forecasting” University of California, USA, 2014

Bin Ye and Jingjing Jiang “Feasibility Study of a Solar-Powered Electric Vehicle Charging Station Model”, 2015.

P. K. Joseph and D. Elangovan, “A review on renewable energy powered wireless power transmission techniques for light electric vehicle charging applications,” J. Energy Storage, vol. 16, pp. 145–155, 2018.

F. Lu H. Zhang and C. Mi, “A two-plate capacitive wireless power transfer system for electric vehicle charging applications,” IEEE Trans. Power Electron., vol. 33, no. 2, pp. 964–969, Feb. 2018.

F. Lu et al., “A dynamic charging system with reduced output power pulsation for electric vehicles,” IEEE Trans. Ind. Electron., vol. 63, no. 10, pp. 6580–6590, Oct. 2016.

R. Tavakoli and Z. Pantic, “Analysis, design, and demonstration of a 25-kW dynamic wireless charging system for roadway electric vehicles,” IEEE J. Emerg. Sel. Topics Power Electron. vol. 6, no. 3, pp. 1378–1393, Sep. 2018

S. Y. R. Hui, W. Zhong, and C. K. Lee, “A critical review of recent progress in mid-range wireless power transfer,” IEEE Trans. Power Electron., vol. 29, no. 9, pp. 4500–4511, Sep. 2014.

F. Liu et al., “Modeling and optimization of magnetically coupled resonant wireless power transfer system with varying spatial scales,” IEEE Trans. Power Electron., vol. 32, no. 4, pp. 3240–3250, Apr. 2017.

Z. Zhang et al., “Wireless power transfer—an overview,” IEEE Trans. Ind. Electron., vol. 66, no. 2, pp. 1044–1058, Feb. 2019.

Y. D. Chung et al., “Design considerations of superconducting wireless power transfer for an electric vehicle at different inserted resonators,” IEEE Trans. Appl. Supercond., vol. 26, no. 4, Jun. 2016, Art. No. 0603605.

Z. Li et al., “A 3-kW wireless power transfer system for sightseeing car supercapacitor charge,” IEEE Trans. Power Electron., vol. 32, no. 5, pp. 3301–3316, May 2017.

D. Patil et al., “Wireless power transfer for vehicular applications: Overview and challenges,” IEEE Trans. Transportation. Electric. vol. 4, no. 1, pp. 3–37, Mar. 2018.

Z. Dai et al., “A Witricity-based high-power device for wireless charging of electric vehicles,” Energies, vol. 10, no. 3, 2017, Art. No. 323.

A. Ibrahim and M. Kiani, “A figure-of-merit for design and optimization of inductive power transmission links for millimeter-sized biomedical implants,” IEEE Trans. Biomed. Circuits Syst., vol. 10, no. 6, pp. 1100–1111, Dec. 2016.

C. Zhang et al., “A novel electric insulation string structure with high voltage insulation and wireless power transfer capabilities,” IEEE Trans. Power Electron., vol. 33, no. 1, pp. 87–96, Jan. 2018.

Z. Luo and X. Wei, “Analysis of square and circular planar spiral coils in wireless power transfer system for electric vehicles,” IEEE Trans. Ind. Electron., vol. 65, no. 1, p. 331–341, Jan. 2018.

B. Deng and Z. Wang, “Research on electric-vehicle charging station technologies based on smart grid,” in 2011 Asia-Pacific Power and Energy Engineering Conference. IEEE, 2011, pp. 1–4.

M. Yilmaz and P. T. Krein, “Review of battery charger topologies, charging power levels, and infrastructure for plug-in electric and hybrid vehicles,” IEEE transactions on Power Electronics, vol. 28, no. 5, pp. 2151–2169, 2012.

Y.-M. WI, J.-U. Lee, and S.-K. Joo, “Electric vehicle charging method for smart homes/buildings with a photovoltaic system,” IEEE Transactions on Consumer Electronics, vol. 59, no. 2, pp. 323–328, 2013.

G. Mauri and A. Valsecchi, “The role of fast-charging stations for electric vehicles in the integration and optimization of the distribution grid with renewable energy sources,” 2012.

W. Tian, J. He, L. Niu, W. Zhang, X. Wang, and Z. Bo, “Simulation of vehicle-to-grid (v2g) on power system frequency control,” in IEEE PES Innovative Smart Grid Technologies. IEEE, 2012, pp. 1–3.

S. Kori, “Vehicle-to-grid power implementation: From stabilizing the grid to supporting large-scale renewable energy,” Journal Current Science, vol. 18, no. 12, 2017

S. Divyapriya, R. Vijayakumar, et al., “Design of residential plugin electric vehicle charging station with a time of use tariff and IoT technology,” in 2018 International Conference on Soft-computing and Network Security (ICSNS). IEEE, 2018, pp. 1–5.

G. Dimitrakopoulos, “Intelligent transportation systems based on internet-connected vehicles: Fundamental research areas and challenges,” in 2011 11th International Conference on ITS Telecommunications. IEEE, 2011, pp. 145–151.

Q. Gong, Y. Li, and Z.-R. Peng, “Optimal power management of plugin hev with the intelligent transportation system,” in 2007 IEEE/ASME international conference on advanced intelligent mechatronics. IEEE, 2007, pp. 1–6.




DOI (PDF): https://doi.org/10.20508/ijrer.v12i1.12821.g8443

Refbacks

  • There are currently no refbacks.


Online ISSN: 1309-0127

Publisher: Gazi University

IJRER is cited in SCOPUS, EBSCO, WEB of SCIENCE (Clarivate Analytics);

IJRER has been cited in Emerging Sources Citation Index from 2016 in web of science.

WEB of SCIENCE in 2025; 

h=35,

Average citation per item=6.59

Last three Years Impact Factor=(1947+1753+1586)/(146+201+78)=5286/425=12.43

Category Quartile:Q4